Returning Customer ?
Don't have an account ?
Showing 451–485 of 485 results
Twist drill, made of cobalt alloyed HSS, acc. to DIN 338, fully ground from the solid. Fitted with a special spiral for good chip removal and greasing materials. Crosswise sharpened acc. to DIN 1412C, point angle 135°, tolerance of diameter h8
One-piece twist drill bit, fully ground from the solid, long version with hexagonal shank for bit holder (1/4“; E 6,3), polished section of the surface of the cone 118°, blank ground
Automatic internal clamping chuck for threading short pipe pieces up to 4″. Quick, tool-free operation, efficient production, internal clamping mechanism, durable clamping. REMS – Made in Germany.
Type B = ½ mm / mm top with 1/2 mm and bottom with 1/1 mm graduation • conform to MID-Code • precise and deep, laser engraved scale, with clear reading • stainless steel, non-glare, matt surface • semi-rigid, with wide cross-section • cm graduation • with identification-no. and certificate of conformity
BETEX WSPE electric hydraulic presses range from 30 to 300 tons, featuring dual-speed pistons, welded frames, adjustable surfaces, precision controls, and optional accessories for diverse and precise pressing tasks.
BETEX NSLS flat hydraulic cylinders: low height, spring return, single acting, 5-150 ton capacity, 6-17 mm stroke, 700 bar pressure, hard chromed piston, roll-polished rams, black nitride finish, compact design.
• for adjusting, levelling etc. • rolled in a rugged plastic box or as stripes in a case with 10 or 5 blades • different material in different width and different length available
• special wear-resistant casting with additionally steel • strong ribbed construction, side surfaces reinforced • measuring surface according to DIN 876 • side surfaces carefully planed or milled
• reading from left to right • with conversion table on the backside • etched graduation for a clear reading • non glare, matt surface • stainless spring steel
Type A = mm / mm top and bottom 1/1 mm graduation • reading from left to right • semi rigid version, with wide cross section • stainless spring steel, with non glare, matt surface • precise, deep graduation with laser engraved, continuing numbers • with identification-no. and calibration certificate
Type B = ½ mm / mm top ½ mm and bottom 1/1 mm graduation • reading from left to right • semi rigid version, with wide cross section • stainless spring steel, with non glare, matt surface • precise, deep graduation with laser engraved, continuing numbers • with identification-no. and calibration certificate
type B = ½ mm / mm top with 1/2 mm and bottom with 1/1 mm graduation • conform to MID-Code • precise, etched scale, with clear reading • stainless steel, non-glare, matt surface • semi-rigid, with wide cross-section • cm graduation • with identification-no. and certificate of conformity
type A = mm / mm top and bottom with 1/1 mm graduation graduation right to left • conform to MID-Code • precise, etched scale, with clear reading • stainless steel, non-glare, matt surface • semi-rigid, with wide cross-section • cm graduation • with identification-no. and certificate of conformity
type A = mm / mm top and bottom with 1/1 mm graduation • conform to MID-Code • precise and deep, laser engraved scale, with clear reading • stainless steel, non-glare, matt surface • semi-rigid, with wide cross-section • cm graduation • with identification-no. and certificate of conformity
For inside TORX® safety screws With hole at drive end Blade matt chrome plated, tip gun metal finish Black plastic-T-handle with suspension hole Chrome-Vanadium 61CrSiV5 / 1.2243
• special wear-resistant casting with additionally steel • strong ribbed construction, side surfaces reinforced • measuring surface according to DIN 876 • side surfaces carefully planed or milled • with supporting points, corresponding to the size of plate • against extra charge we supply the plates with handle and with protective wooden cover
• suitable for Control- and Testing Plates • from about 1200×800 mm size we recommend single supporting feets • solid steel construction • for a working height of approx. 800 mm
• graduation on front- and rearside • reading from left to right • with two straight ends without whole • precise, deep laser engraved scale • non-glare, matt surface, with clear reading • with detachable magnetic inserts • non-glare, matt surface
type B = ½ mm / mm top ½ mm and bottom 1/1 mm graduation reading from right to left • semi rigid version, with wide cross section • stainless spring steel • non glare, matt surface • etched graduation for a clear reading • up to 2000 mm in a vinyl bag
Type D = inch / mm top 1/64 ; 1/32 and 1/16 inch graduation, bottom ½ mm and 1/1 mm • semi rigid version, with wide cross section • stainless spring steel • non glare, matt surface • etched graduation for a clear reading • up to 2000 mm in a vinyl bag
Spanner with 02 sizes open, non-sparking, according to DIN 3110, ISO 3318, ISO 1085, ISO 10102. Material Cu-Be. Made by ELORA Germany. Other size upon on request.
acc. to DIN 2014/32/EU • reading from left to right or right to left • precise, deep graduation laser engraved, continuing numbers • non glare, matt surface • stainless spring steel • with identification-no
acc. to workshop grade • stainless spring steel • non glare, matt surface • etched graduation for a clear reading • graduation reading from left to right, zero-point in the middle • top and bottom 1/1 mm graduation
With straight edge and point working end hardened Material: high grade tool steel C45 / 1.0503. ELORA Germany.
Two spiraled main cutting edges in fully ground quality with stepped cylindrical shank Ø 13 or 16 mm.
2500 – 5000 rpm. e.g. Ø 16 mm 2500 rpm in soft wood. Further details in the speeddiagram
High cutting performance with minimal effort Cutting edge hardness: 63-65 HRC Chrome-plated, polished Maximum stability under load by additional inductive hardening For hardened steel wire, piano wire (tensile strength 2300 N/mm²)
For standard purposes, like thickness measuring between narrow slots and for automotive and engine industry. Hardened spring steel, conical shaped blades, 100mm lenght.
• for simple workshop use • made of steel • chromed version • type A = without graduation, type B = with mm graduation • graduation black etched, bevel edge matt chrome finish
• rugged metal housing, weighing plate made from stainless steel • large LCD display, digit height 20 mm • easy 3-/4-button operation, self-explaining • operation by battery or main supply, switchable
Two straight main cutting edges with chip breaking flutes. With stepped cylindrical shank Ø 13 or 16 mm.
2200 – 4000 rpm. e.g. Ø 16 mm 2200 rpm in soft wood. Further details in the speed diagram